Receipt Printer Troubleshooting: Fix Common Problems

Thermal receipt printer printing blank, faded or not at all? Find your problem below for the likely cause and a step-by-step fix - for USB, Bluetooth and LAN printers.

Quick checks before anything else

These five checks fix most receipt printer problems in under a minute.

  • The printer is switched on and the power light is steady (not red or blinking)
  • The paper roll is loaded with the printable side facing the print head
  • The paper cover is closed firmly until it clicks
  • The cable is plugged in - or the printer is paired over Bluetooth, or on the same Wi-Fi / LAN
  • The correct printer and paper size (58 mm or 80 mm) are selected in Baskit
Thermal receipt printer being checked for problems

Common receipt printer problems and how to fix them

Find the problem you're seeing, check the likely causes, and try the fixes in order.

Thermal printer printing blank paper

Likely causes

  • Paper roll loaded upside down
  • Paper is not thermal paper
  • Print head disconnected or damaged

How to fix

  1. Flip the roll so the shiny, coated side faces the print head
  2. Scratch the paper with a fingernail - thermal paper turns dark. If it doesn't, replace it
  3. Print a self-test page; if that is blank too, contact service

Faded or light print

Likely causes

  • Low-quality or old thermal paper
  • Print density set too low
  • Dirty print head
  • Weak power adapter or low battery

How to fix

  1. Use good-quality thermal paper stored away from heat and sunlight
  2. Increase print density / darkness in the printer settings or driver
  3. Clean the print head with an isopropyl alcohol swab
  4. Use the original adapter, or charge a portable printer fully

Receipt printer not printing at all

Likely causes

  • Wrong printer selected in Baskit
  • Cable loose, or Bluetooth / network disconnected
  • Driver missing or wrong (Windows)
  • Printer showing an error (paper out, cover open)

How to fix

  1. Select the right printer again in Baskit's printer settings
  2. Reconnect the cable, re-pair Bluetooth, or check the network
  3. Install the correct driver from the drivers folder
  4. Clear the error - reload paper and close the cover

Printing garbage or strange characters

Likely causes

  • Wrong driver or printer mode
  • Wrong printer model selected
  • Paper width setting wrong

How to fix

  1. Use an ESC/POS-compatible driver or mode
  2. Select the correct printer model in the driver
  3. Set the paper width to 58 mm or 80 mm to match your roll

Print cut off, too small or too wide

Likely causes

  • Paper size set to 80 mm on a 58 mm printer (or the reverse)
  • Margins or scaling set in the driver

How to fix

  1. Set the correct paper size in Baskit and in the printer driver
  2. Turn off scaling and set margins to zero in the driver

Bluetooth printer not connecting

Likely causes

  • Printer not paired with this phone
  • Already connected to another phone or tablet
  • Printer battery low or too far away
  • Phone Bluetooth or location permission off

How to fix

  1. Pair the printer in Bluetooth settings, then select it in Baskit
  2. Disconnect it from other devices, or switch them off
  3. Charge the printer and keep it within a few metres
  4. Turn on Bluetooth and allow Baskit's Bluetooth / nearby devices permission

LAN or Wi-Fi printer not found

Likely causes

  • Printer's IP address has changed
  • Printer and device on different networks
  • Network cable loose or router restarted

How to fix

  1. Print a self-test page to see the current IP address and enter it in Baskit
  2. Connect both to the same router / Wi-Fi
  3. Give the printer a fixed (static) IP so it doesn't change

Paper jams or feeds crooked

Likely causes

  • Roll too large or wrong core size
  • Roll loaded at an angle
  • Torn paper stuck inside

How to fix

  1. Use the roll size your printer supports
  2. Reload the roll straight, with a little paper pulled out past the cutter
  3. Open the cover and gently remove any torn pieces

Auto-cutter not cutting

Likely causes

  • Paper stuck in the cutter
  • Cutter turned off in settings
  • Worn or broken cutter blade

How to fix

  1. Switch off, open the cover and clear the paper
  2. Enable auto-cut in the driver or Baskit's print settings
  3. If it still fails, the cutter needs service

Cash drawer not opening

Likely causes

  • RJ11 cable not in the printer's drawer port
  • Open-drawer setting turned off
  • Drawer voltage doesn't match the printer
  • Drawer key in the locked position

How to fix

  1. Plug the drawer cable into the printer's DK / drawer port (not the network port)
  2. Turn on "open cash drawer" in the print settings
  3. Check the drawer matches your printer's voltage (usually 24V)
  4. Turn the drawer key to the auto-open position

Red light blinking or beeping

Likely causes

  • Paper out or nearly out
  • Cover not closed
  • Print head overheated
  • Cutter jam

How to fix

  1. Load a new roll
  2. Close the cover firmly
  3. Switch off and let the printer cool for a few minutes
  4. Clear the cutter jam

Printing very slowly

Likely causes

  • Bluetooth printer too far away
  • Large logo image on the bill
  • Weak power adapter or low battery

How to fix

  1. Keep the printer closer to the phone
  2. Use a smaller, black-and-white logo
  3. Use the original adapter or charge the printer

Need a driver? Download receipt printer drivers. Cash drawer still not working? See our cash drawer guide.

How to print a self-test page

A self-test page tells you whether the problem is the printer itself or the connection to your phone or PC.

Switch the printer off

Make sure paper is loaded and the cover is closed.

Hold the FEED button

Press and hold FEED while you switch the printer on.

Release when it prints

Let go when the printer starts printing. The exact steps can vary by brand - check your manual.

Read the test page

It shows the model, settings, interface and - for LAN printers - the IP address. If the test page prints well, the printer itself is working.

What the error light usually means

Light / sound Usual meaning What to do
Steady green / blueReadyNothing - the printer is fine
Red light onPaper out or cover openLoad paper and close the cover
Red light blinkingCutter jam or print head too hotClear the jam, or switch off and let it cool
BeepingAn error the printer can't clear by itselfCheck paper, cover and cutter; restart the printer

Light colours and beep patterns differ between brands - your printer's manual has the exact meaning.

How to clean a thermal printer head

A dirty print head is the most common cause of faded or streaky receipts.

Switch off and let it cool

The print head gets hot - wait a few minutes after printing.

Open the paper cover

Remove the paper roll so you can reach the print head.

Wipe with alcohol

Gently wipe the print head (the dark strip) with a cotton swab or pen dipped in isopropyl alcohol.

Let it dry, then reload

Wait until it is completely dry, reload the paper and print a test.

Never scrape the print head with anything hard or sharp - it scratches easily and is expensive to replace.

How to prevent receipt printer problems

Use good thermal paper

Cheap paper fades fast and leaves dust that dirties the print head.

Store paper properly

Keep rolls away from heat, sunlight and moisture.

Clean the print head

Clean it every few rolls, or when print starts to fade.

Fix the IP address

Give LAN printers a static IP so Baskit can always find them.

Use the original adapter

A weak adapter causes faded print and random restarts.

Keep drivers updated

Use the latest driver for your printer model on Windows.

When to call service

  • The self-test page is blank or has missing lines
  • The print head is scratched or burnt
  • The cutter is broken or makes a grinding noise
  • The printer doesn't switch on with a working adapter
  • There is physical damage, liquid spills or a burning smell
Contact support →

Receipt printer troubleshooting FAQ

Why is my thermal printer printing blank?

Usually the paper roll is loaded upside down, so the coated side isn't facing the print head, or the paper is not thermal paper. Flip the roll, or scratch the paper - thermal paper turns dark when scratched.

How do I fix faded print on a receipt printer?

Use better-quality thermal paper, increase the print density in the printer settings, clean the print head with isopropyl alcohol, and make sure the printer has enough power.

Why is my receipt printer not printing?

Check that the right printer is selected in Baskit, the cable or Bluetooth/network connection is working, paper is loaded and the cover is closed. On Windows, make sure the correct driver is installed.

Why is my receipt printer printing strange characters?

The driver or printer mode is wrong, or the wrong model is selected. Use an ESC/POS-compatible driver and set the correct paper width (58 mm or 80 mm).

Why won't my Bluetooth printer connect?

The printer may not be paired, may be connected to another device, or the battery may be low. Pair it in Bluetooth settings, disconnect other devices, charge it and allow Baskit's Bluetooth permission.

How do I find my LAN printer's IP address?

Print a self-test page by holding the FEED button while switching the printer on. The IP address is printed on the test page.

How do I clean a thermal printer head?

Switch off and let it cool, open the cover, wipe the print head gently with a cotton swab dipped in isopropyl alcohol, let it dry and reload the paper.

Why is my cash drawer not opening?

Check the drawer cable is in the printer's drawer (DK) port, the open-drawer setting is on, the drawer voltage matches the printer and the drawer key is in the auto-open position.

Still not printing?

Our support team can help you connect and set up your receipt printer with Baskit.

📅

Book Your Free Demo

Get a personalized walkthrough of Baskit and see how it can simplify your business.

Free personalized demo • Quick setup • Expert guidance